top of page

Chapter 7: The Reference Ceiling And Distance Tax

13 hours ago
4 min read
A high power amplifier in a lightning storm


Framework 2:

The Reference Ceiling

&

Framework 3:

The Distance Tax






The Reference Ceiling


Reference Level is best understood as a maximum design envelope rather than a mandatory listening target.


Manufacturer Perspective (Cody Hiebert). Reference Level establishes the maximum dynamic range a playback system should be capable of reproducing. It does not imply that every listener should routinely listen at that level, nor that every piece of content will require it for the simple reason that mixing studios and systems are standardized to “Reference” but then use about 20 to 30 db down from their design limit; which in simple math is using about 0.1% to 1% of the design, while maintaining the reality that this severe neutering does not actually guarantee perfect linearity at all points at all times. If RP22 is going to establish a worst case scenario as a basis for the headroom they are asking for, the tests and verification should likewise be the worst case. And nothing is more worst case than a full scale, long duration, RMS fully loaded sine sweep.


For a ‘Main’ speaker, our ‘Reference Level’ peak Target is 105 dB as a sine wave. much of a main speaker’s operating range will be above the ‘transition frequency’, wherever that may be in any given room, and it differs depending on the acoustics. But for our example, close enough, and it is an easy calculation to standardize.


In my calculator, we can predict the ‘power’ required (equivalent voltage at nominal impedance) given an input of a loudspeaker’s voltage sensitivity, distance, and target output level, in our case 105 dB.


I’m going to grab specifications provided by a pretty mainstream manufacturer that look plausible for the loudspeaker, typical of many quality loudspeakers in the price range of $1,500 each to run our examples, a pretty ‘Full-range’ tower speaker, in terms of frequency response anyway. You infrasonic bass heads, keep the cackling down, I know, I know. If it’s not reaching easily into single digits, not really ‘full-range’. Most of the kids who didn’t eat the Play-Doh find it ‘full-range’ enough.




This is neither an endorsement nor indictment of the product. I just wanted to grab a real life example. These look cool, and lots of people know SVS as a reputable brand that represents reasonable or better performance results for the money spent. I am using it as an example because it is representative of a lot of very decent home audio loudspeakers.


FWIW, all 13 reviewers gave it 5 stars, so that’s worth something. More to the point, I’m pulling specifications that are both plausible as well as consistent with what the RP22 example was using to represent a predictor of target capabilities.



The Distance Tax is the exponential increase in system resources required to maintain the same direct sound level as listening distance increases.


Every additional meter increases the demands placed upon the loudspeaker, amplifier, thermal capacity, and distortion performance. Distance is not free. Distance is paid for in watts, displacement, distortion, or money.


So salient data to our simplistic calculator:

  • 87 dB@2.83V@1Meter

  • Recommended amplifier power 20-300 watts


Let’s see how this ‘works’ with ‘reference level’ of 105 dB output at the main listening position. Main listening position requires distance values. Let’s look at a variety of options, in 1 meter increments, from 1 meter (near-field mixing monitor distance, and a standard for loudspeaker specifications) to 4 meters not a particularly extreme distance, and see what that requires of amplifier ‘power’ and associated loudspeaker ‘Power Handling’ (admittedly a slippery limit).



So with these five star tower speakers, we can see that if you use them as nearfield

mixing monitors, 1 meter away, from an SPL standpoint, we’re probably fine. 63 ‘watts’ of equivalent voltage at 8 ohms, or peak RMS voltage of 22.5 volts, or waveform peak voltage of 31.8 volts, any decent AVR should be able to swing that, at least a couple channels at a time. If the load dips to 4 ohms, that would equate to 126 watts/channel. Not insignificant, but most AVRs will probably not fall short by much, if they do. But most people are probably not using them at 1 meter distance.


2 meters is probably near the minimum plausible for a very small ‘theater’ listening space. Maybe good for a small couch and cuddle time while watching a movie. We now need 45 volts RMS, or 63.6 waveform peak voltage, equivalent to 253 watts at 8 ohms, and into the nominal 6 ohms, 337 watts, into 4 ohms if the speaker dips there, potentially, 505 watts. Uh, probably not the typical AVR. Probably not AVR power at all. Okay, well about that Certification Badge, how much did we pay extra for that? Don’t worry, just upgrade!


Enter your hero, the outboard power amplifier! If you want to do what you thought your AVR should be capable of doing all by itself, thankfully you can just buy another box. In all fairness, outboard power amps are a standard feature in any moderate dedicated audio space.


Thanks to the development in manufacturing of modular Class D amplifiers by Hypex, ICEPower, Purfi, and etc, there are a slew of reasonably affordable power amplifiers that have specifications that fit the theoretical requirements of this case. This is genuinely pretty cool for people who can now have significantly more output capability than what typically fits in an AVR, with reasonably more expenditure and rack space. Buckeye and VTV are forum favorites, but manufacturers that essentially buy in bulk, install in a chassis with connectors, give it a name and a special superiority story are popping up all over.


There are nuances to that assumption, in terms of whether the amplifiers can actually provide what the specifications imply without engaging protection circuits or ‘soft clipping’, over the entire operating range. But we’re shelving that, as we’re still in simplistic mode, and will just say they do.


Good to go, so long as your loudspeaker holds together. It is often said by audio salesmen (I used to be one) about any loudspeaker they are trying to sell, that “it can handle more power for short periods if it’s clean. ” That can be true. It usually is. In this case, the theoretical nominal power required at 6 ohms (337 ‘watts’) is just barely beyond the recommended power amplifier range, so if I was betting my lunch money, I would bet on survival.


Back that up to 3 meters, or just short of 10 feet.

Things just got serious.


Originally published by Totally Hypeless


Comments


bottom of page